MK Diamond Products MK-770 EXP Owner's Manual

MK-770EXP TILE SAW OWNER'S MANUAL, PARTS LIST &OPERATING INSTRUCTIONSwww.mkdiamond.com05.2015Caution: Read all safety and operating instructi

10ON(())ON(())ON(())Tous les visiteurs et les enfants doivent se tenir à bonne distance de la zone de travail. Maintenir une distance d'utilisati

11Voir les accessoires recommandés dans le manuel d'utilisation. L'utilisation d'accessoires inadéquats peut augmenter le risque de bl

12Avant d'utiliser un outil électrique, vérifier s'il y a des pièces endommagées. Examiner soigneusement les pièces et dispositifs de protec

13AVERTISSEMENT SUR LA POUSSIÈRE DE SILICELa rectication/la coupe/le perçage de la maçonnerie, du béton, du métal et d'autres matériaux contenan

14AVERTISSEMENTAVERTISSEMENTPour réduire le risque d’électrocution, garder toutes les connexions au sec et au-dessus du sol. Les circuits et prises su

15WARNINGWARNINGTo reduce the risk of electrocution, keep all connections dry and off the ground. A Ground Fault Cir-cuit Interrupter (GFCI) should be

16MK-770EXP SAW SAFETYWARNINGIn order to prevent electrical

17To avoid the possibility of the appliance or plug receptacle getting wet, position the machine to one side of a wall mounted receptacle. This will

18MK-770EXP SAW SAFETYWARNINGUse of undersized extension cor

19NOTES

2Congratulations on your purchase of a MK-770EXP Saw Tile Saw. We are certain that you will be pleased with your purchase. MK Diamond takes pride in

20SAFETY LABEL LOCATIONSSafety labels contain important safety information. Please read the information contained on each safety label. These labels a

21TILE SAW SPECIFIC WARNINGSWear eye protection.Use splash guard for every operation for which it can be used.Disconnect saw before servicing, when ch

MK-770EXP TILE SAW OWNER'S MANUAL, PARTS LIST &OPERATING INSTRUCTIONSwww.mkdiamond.com04.2014Caution: Read all safety and operating instructi

231. The MK-770EXP weighs approximately forty-six (46) pounds; use care when transporting.2. Never transport the MK-770EXP with water in the Wate

(D)Install the Height Adjusting Knob through the Post into the Cutting Head and tighten the Knob24Follow the assembly instructions to prepare your MK-

25(E)Using the Blade and Shaft Wrenches, loosen and remove the Retaining Nut and Outer Flange(D)Place the Shaft Wrench between the Inner Blade Guard a

26(A)Loosen Adjustable Cutting Guide retaining thumbscrew and place it over the Movable Cutting Table, Ruler/Stop(B)Place the Adjustable Cutting Guide

27(B)Verify the Movable Cutting Table moves freely(A)Ensure the ON/OFF Switchis in the OFF position(C)Inspect the Diamond Blade for damage – verify th

If cutting dry DO NOT connect the water pump.NOTE:28EXTERNAL WATER SOURCE(A)Remove the Drain plug(C)Fill the external container until water complete

29NOTE: When using the re-circulation method, the water should be changed often for longer pump lifeIf using a portable generator to provide power, e

3TABLE OF CONTENTS SAFETYSafety Messages 4 Damage Prevention Message 4 General Safety Precautions 4-7 California Proposition 65 Message 8Canadian

30(B)Position the Adjustable Cutting Guide to desired cut length (A)Loosen the Adjustable Cutting Guide retaining thumbscrew(C)Tighten the retaining t

31(B)Pivot the Cutting Head to the 45º cutting position(A)Loosen the Cutting Head Pivot, Retaining Knob(C)Tighten the Cutting Head, Pivot Retaining Kn

32(K)Turn the motor OFF when work is complete(J)Perform the cut(L)Return the Cutting Head to the upright position when complete MK-770EXP SAW

33(B)Place the Dual 45º Flat Angle Guide on the Ruler/Stop(A)Remove the Adjustable Cutting Guide(C)Position the Dual 45º Flat Angle Guide and tighten

34(B)Place the Protractor on the Ruler/Stop(A)Remove the Adjustable Cutting Guide(C)Set the desired angle on the Protractor Gage(E)Position the Protra

(A)Place the Water Pumpin an external container.(B)Run the saw until clearwater is seen at the bladecooling ports (Approx. 1 minute).35(C)Ensure the O

36(B)Unplug MK-770 EXP(A)Ensure the ON/OFF Switch is in the OFF position(C)Lubricate the Guide Bar(B)Remove the Inner Flange(A)Remove the Diamond Blad

37 MK-770EXP SAW MAINTENANCE(E)Remove the Blade Guard then clean and Lubricate the Blade Guard Pivot Shaft(D)Clean a

38(B)Reduce cooling flow by Pressing down on the Flow Adjusting Clamp(A)Increase cooling flow by releasing the Flow Adjusting ClampFLOW ADJUSTMENT If

39 MK-770EXP SAW MAINTENANCE(E)Verify cooling flow on both sides of the blade(D)Turn the motor ON(F)Cut the Dressing

4MK-770EXP SAW SAFETYRead and follow all safety, operating a

40(B)Remove Retaining Nut and Outer Flange(A)Open the Outer Blade(C)Remove Diamond Blade from Blade Shaft(E)Install the Retaining Nut and Outer Flange

41(B)Remove Water Pan. Inspect Tile Saw for damage(A)Remove Tile Sawfrom Power Source(C)Inspect Diamond Bladefor damage MK-770EXP SAW

42(E)Check for Gap between the Square and Straightedge(D)Move Straightedge to the other side, and place the Square on that side of table(F)If Gap exis

43(B)Locate the 90°Adjustment Screw(A)Position the Cutting Headto the 45º Cutting Angle(C)Rotate 90° Adjustment Screwclockwise or counter-clockwiseto

44(B)Position Square flat on MovableCutting Table against Ruler/Stop(A)Pull Movable Cutting Tableto front of Tile Saw(C)Position front of Squareagains

45(B)Position the Cutting Headto the 45° Cutting Angle(A)Remove Blade Guard(If not done Previously)(C)Place Square on the Movable Cutting Table and po

46(B)Check for proper rotation(A)Check for Smoothness or “Glazing” (Dress blade if needed)(C)Ensure the Blade Core is not bent and Arbor is not out of

47(B)Remove the Cooling Transfer Tube from the Blade Guard inlet(A)Check cooling flow Adjusting Clamp open(C)Place Pump into a bucket of water and che

48(A)Verify all plugs are fully installed(C)Check power source voltage is 115V – if not 115v, move to another circuit(B)Verify circuit breaker not tri

49NOTES

5MK-770EXP SAW SAFETYON(())ON(())ON(())All visitors and chil

50 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 29 30 31 32 33 34 35 MK-770EXP SAW

51ITEM DESCRIPTION PART # QTY.1 WASHER, FLAT, USS, 3/8 101360 12 HOSE, VINYL, 1/4X3/8 (6.0") 132951 13 WRENCH, TILE SAW NUT 15/16 134684 14 PAN,

52 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 ITEM DESCRIPTION PART # QTY.1 FLANGE, OUTER, 2-3/8 135830 22 NUT, HEX, 5/8-18

53 MK-770EXP SAW EXPLODED VIEW & PARTS LIST 1 2 3 4 5 6 7 8 9 5 ITEM DESCRIPTION PART # QTY.1 BAR, GUIDE PLATED MK-

54 1 2 3 4 5 ITEM DESCRIPTION PART # QTY.1 WHEEL, ROLLER TSAW 151799 12 NUT, HEX HEAD 1/4-20 X 1-1/2" 151893 13 SCREW, HEX HEAD 1/4-20 X 1-1/

55ITEM NUMBER DESCRIPTION1. 139295 MK-200, 7 x 5/8 Arbor2. 139311 MK-215, 7 x 5/8 Arbor3. 153293 MK-315, 7 x 5/8 Arbor5. 134577-MK Dual 45° Flat Angle

56ORDERING INFORMATIONYou may order MK Diamond products through your local MK Diamond distributor or, you may order direct from MK Diamond.When orderi

57 MK-770EXP SAW CONTACT & WARRANTYCONTACTPlease contact MK Diamond Products, Inc. Customer S

MK-770 EXP TILE SAWOWNER'S MANUAL & OPERATING INSTRUCTIONS MK Diamond Products, Inc.1315 Storm ParkwayTorrance, CA 90501Toll-Free: (800) 421

6MK-770EXP SAW SAFETYConsult the owner’s manual for recommende

7MK-770EXP SAW SAFETYBefore using a power tool, check for dama

8MK-770EXP SAW SAFETYSawing and drilling generate dust. Exce

9MK-770EXP SAW DE SéCURITéLisez et suivez toutes les consignes de sécur